![]() I'm the former Product Manager for Malwarebytes and I haven't enabled Self-Protection in over 2 years, that's how confident I am that it isn't needed. I know that the issue isn't solved (merely a workaround), but at least the file explorer is speedy again! Thank you to everyone who provided assistance to me. Anyway, I suppose that I can live without the self protection module until the MBAM team fixes this. When I said that it was "sluggish", I meant that switching between folders and things of that nature took a second or two instead of being snappy like they should be. Turning off the self protection module seems to stop it from happening. The explorer issue on the other hand is a Malwarebytes thing. When I mentioned that programs were slow to load, I was testing with a program that itself had a bug that caused that that has been resolved by the developers. If you turn that off, does it help your situation at all? Also, can you clarify exactly what's happening? You mention programs are slow to load and explorer is sluggish, but any more details would help helpful This can be found in the same Settings -> Protection, but just down a little bit farther. There is one more module to test as well, that's Self-Protection. If suggestion does not work, I will try this later. This is rather time-consuming and I haven't had a chance to do this yet. Please do that one at a time for each module and let me know how it goes. So again, start with Ransomware Protection, turning it off, then rebooting the system, then performing your test to see how performance is. In order to test, please do the same test you did before where you disabled each module one by one, but this time instead of just disabling it then testing, reboot the system then perform your test to see if the issue is resolved. Second, while it isn't too likely, it is at least somewhat possible that the issue is that one of the other modules isn't fully terminating as it is supposed to. ![]() I will petition them once again to change this, but at this time there is no known workaround short of exiting completely as you did. What this means is that if Malware Protection is the problem, then turning that module off probably won't do anything to help which makes me lean towards that as being the cause. Two things, first is the fact that, at least the last I heard from the Devs, whenever Malware Protection is disabled it's never truly "turned off", instead it actually just goes into a sort of "allow all" mode so that nothing is detected as a threat. Joy, OK, that definitely gives me some ideas. Please let us know how it goes and please provide the requested logs for the sake of our Developers so that they can troubleshoot the issue further in case it was a problem with the installer. Once that's done, be sure to reboot your system at least once after the installation is complete, then test to see if the issue is fixed or not. Click the Clean button, and allow it to restart your system and then reinstall Malwarebytes, either by allowing the tool to do so when it offers to on restart, or by downloading and installing the latest version from here.Next, click Advanced Options on the main page (not Get Started).Run the Malwarebytes Support Tool once more.Once that's done, go ahead and do the following to see if it corrects the problem: In order to documented for the Developers, please do the following:ĭownload and run the Malwarebytes Support ToolĪccept the EULA and click Advanced Options on the main page (not Get Started)Ĭlick the Gather Logs button, and once it completes, attach the zip file it creates on your desktop to your next reply ![]() It's possible that one or more of the components/files wasn't updated properly and may still be an older version resulting in this issue. Before submitting your reply, be sure to enable "Notify me of replies" like so:Ĭlick "Reveal Hidden Contents" below for details on how to attach a file: Please attach the file in your next reply. You will be presented with a page stating, " Welcome to the Malwarebytes Support Tool!"Ī progress bar will appear and the program will proceed to gather troubleshooting information from your computerĪ file named mbst-grab-results.zip will be saved to your Desktop Place a checkmark next to Accept License Agreement and click Next You may be prompted by User Account Control (UAC) to allow changes to be made to your computer. ![]() Once the file is downloaded, open your Downloads folder/location of the downloaded fileĭouble-click mb-support-X.X.X.XXXX.exe to run the program NOTE: The tools and the information obtained is safe and not harmful to your privacy or your computer, please allow the programs to run if blocked by your system. If you haven’t already done so, please run the Malwarebytes Support Tool and then attach the logs in your next reply: Endpoint Detection & Response for Servers
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |